Products
At KW Hydraulik you will find a wide range of hydraulic power units, tools and machines. Visit our online shop today.
KWDY - Power compressed air for your vehicle, power for Mercedes Sprinter with reinforced power take-off (PTO+)
KDY-3-6,5-P13-PTO-GEAR-MB
(5) Vehicle: Mercedes Sprinter 2 RWD + PTO ab 2018
The KWDY system combines a hydraulically driven power generator and a screw compressor (1,300 l/min at 10 bar) for fixed installation in vans with a reinforced power take-off(PTO+, 40 kW), e.g. Mercedes Sprinter, VW Crafter or MAN TGE. It supplies 6.5 kVA of power (400/230 V) and compressed air for demanding applications such as earth rockets or tools on the construction site. The unit is based on proven Dynaset technology and is supplied complete with hydraulic pump, generator, compressor, oil tank, oil cooling system, filter and all vehicle-specific components. Installation included. Further installation solutions for vehicles with power take-off can be found here. Note: Oil cooling for the PTO is required on the vehicle. The PTO must be prepared for hydraulic pumps (multi-tooth shaft). Screw compressor with 1300 l/min. at 10 bar (e.g. for ground rockets)Power generator 6.5 kVA (400/230 volts)System for installation in vehicles with reinforced power take-off (40 kW), e.g. VW CRAFTER, MAN TGE, MERCEDES SPRINTER, with oil cooler for the power take-off* for increased continuous output.The engine of your van serves as the drive for this system.Equipment:230 Volt / 14.2 A / CEE socket blue or SCHUKO400 Volt / 10 kVA / 9.4 A / CEE socket redAir compressor, 1300 l/min. at 10 barScope of delivery:Hydraulic pump with adapter for power take-off*Note: The oil cooling for the power take-off must be ordered from the vehicle manufacturer!Power generator,Air compressorHydraulic oil tank, oil cooling, oil filter,vehicle-specific cables and adaptersPrice includes installation. (hoses, etc.)* The power take-off must be prepared for the connection of a hydraulic pump; multi-tooth shaft.
Price on request
KWF COMPACT AIR 650/10 - Generator-compressor unit 230V/400V/10 bar for workshop vehicles
KWF-E5-10-P6
The KWF COMPACT AIR 650/10 is a pre-assembled hydraulic power unit for permanent installation in service and workshop vehicles, developed by the manufacturer FEP. The system combines power generation (up to 10 kVA) and compressed air supply (650 l/min at max. 10 bar) in a compact frame module.Thanks to the optional auxiliary drive(PTO), the power pack is suitable for vehicles with or without PTO preparation. It is driven by the vehicle engine. The 25-litre pressure accumulator, an integrated oil tank with cooling and filter as well as a digital control unit ensure professional continuous operation.Ideal for mobile workshops and customised vehicle conversions.Further installation solutions can be found here.Complete unit in a frame. Delivery only to specialised companies.HYDRO COMPACT AIR 650/10 is a unit for installation in service and workshop vehicles. It can be installed in vehicles with and without an existing PTO power take-off* on the transmission.The engine of your van serves as the drive.Installed in the frame:Power generator 10 kVA, depending on the installation ratio, this generator supplies 5,000 to 8,000 watts (400 volts)230 Volt / 5 kVA / 16 A / CEE socket blue or SCHUKO400 Volt / 10 kVA / 16 A / CEE socket redAir compressor, max. 650 L/min. at max. 10 bar, with 25 litre pressure accumulator, connection BSP1/2" IGHydraulic oil tank, oil cooling, oil filter, control valve, pipeworkControl unit with digital display of the most important functionsSupplied without connection hoses* The power take-off must be prepared for the connection of a hydraulic pump; multi-tooth shaft.
Price on request
KWF ELECTRIC BELT - Power for your workshop, tradesman or service vehicle, 230 Volt / 400 Volt
KWF-E5-10-PTO-BELT.4
(5) Vehicle: Dacia Dokker FWD ab 2013
HYDRO COMPACT ELECTRIC - PTO-BELT supplies mobile power for your service and workshop vehicles. It can be fitted to vehicles with front/rear and all-wheel drive without an existing PTO power take-off on the transmission.The engine of your van serves as the drive for the generator, compressor and hydraulic pump.For this purpose, a hydraulic pump is mounted on the alternator belt, which is engaged as required using the magnetic clutch supplied. The hydraulics drive the system. Equipment: 230 Volt / 5 kVA / 16 A / CEE socket blue or SCHUKO400 Volt / 10 kVA / 16 A / CEE socket redScope of delivery:Hydraulic pump with magnetic coupling, bracket, beltPower generator unit with hydraulic tank, oil cooling, filter, Control unit with vehicle-specific cables and adapters Price includes installation.The vehicle must be delivered to and collected from us for installation in your vehicle. These transfer costs are not included.
Price on request
KWF ELECTRIC GEAR - Power for your workshop, tradesman or service vehicle, 230 Volt / 400 Volt
KWF-E5-10-PTO-GEAR-VW2
(5) Vehicle: VW Crafter 2 RWD + PTO ab 2015
The HYDRO COMPACT ELECTRIC - PTO-GEAR system from FEP supplies mobile power via the vehicle's power take-off (PTO). The unit is permanently installed and is ideal for workshop, service or tradesman vehicles with rear-wheel drive. Once installed, the hydraulic pump generates power for the generator at a stable frequency - 230 V to 5 kVA or 400 V to 10 kVA, available via CEE or SCHUKO sockets. Included in the scope of delivery: Hydraulic pump with PTO adapter, power generator with tank, oil cooling, filter, control unit and vehicle-specific cabling. Installation at KW Hydraulik, vehicle delivery required. Further installation solutions can be found here. HYDRO COMPACT ELECTRIC - PTO-GEAR supplies mobile power for your service and workshop vehicles.Installation kit in rear-wheel drive vehicles with existing PTO auxiliary drive*.The engine of your vehicle serves as a drive for a hydraulic pump. The energy generated in this way can drive our generator anywhere in the vehicle, which supplies electricity at a constant frequency. Equipment: 230 Volt / 5 kVA / 16 A / CEE socket blue or SCHUKO400 Volt / 10 kVA / 16 A / CEE socket redScope of delivery:Hydraulic pump with adapter for power take-off*Power generator unit with hydraulic tank, oil cooling, filter, Control unit with vehicle-specific cables and adapters Price includes installation.The vehicle must be delivered to and collected from us for installation in your vehicle. These transfer costs are not included.* The power take-off must be prepared for the connection of a hydraulic pump; multi-tooth shaft.
Price on request
Discount %
KWF WATER HBW200 - Hydraulic high-pressure cleaner
KWF-HWB200
The KWF WATER HBW200 hydraulic high-pressure cleaner from FEP is the perfect solution for mobile use on commercial vehicles and vans up to 7.5 tonnes. The powerful high-pressure cleaner pump with hydraulic motor delivers a water flow rate of 25 litres per minute at a pressure of 150 BAR. As it is driven directly by the vehicle engine, no harmful exhaust fumes are emitted from the unit, which means it can also be operated safely in the cargo area. The KWF WATER HBW200 requires a hydraulic supply of 20-40 litres at 200 bar and is equipped with a pressure gauge and a pressure relief valve. The system is optionally available with a 90-litre water tank. It is conveniently operated via a washing lance with high and low pressure nozzles, connected to an automatic hose reel and 18 metres of hose. The compact dimensions of 445 x 720 x 500 mm (height) facilitate integration into existing vehicle superstructures. Discover all applications for hydraulic systems in commercial vehicles on our overview page Hydraulics for commercial vehicles and vans up to 7.5 tonnes! High-pressure cleaner pump with hydraulic motor with a water flow rate of 25 litres per minute and a pressure of 150 BAR.Driven by the vehicle engine, no harmful exhaust fumes are emitted from the unit, enabling safe operation in the cargo area.FeaturesHydraulic requirement: 20-40 litres at 200 barPressure gauge and pressure relief valveAvailable with 90 litre water tankWash lance with high and low pressure nozzle, on a hose reel with automatic spring reel with hose length 18 metresDimensions 445 x 720 H. 500 mm
Selling price: €4,862.00 Regular price: €5,720.00 (15% saved)
KWF-COMBY - Electric air-hydraulic welding for VW CRAFTER with power take-off (PTO) up to 2016
KWF-E5-10-S30-P8-H-PTO-VW1
(5) Vehicle: VW Crafter 1 RWD + PTO bis 2016
The KWF-COMBY - HYDRO COMBY SW-F300 - PTO-GEAR model is a compact, multifunctional unit for service and workshop vehicles with power take-off (PTO) - for example for the VW Crafter (up to model year 2016). The system is driven directly by the vehicle's engine via a hydraulic pump and combines power generation, compressed air supply, welding technology and hydraulic function in a single system. The equipment includes a 230 V output (5 kVA / 16 A / CEE socket blue or Schuko) and a 400 V output (10 kVA / 16 A / CEE socket red). The integrated welding unit supplies up to 300 A welding current, has a connection for SK 35/50 plugs and an interface for a remote control. The air compressor generates 1,000 l/min at 12 bar with a 25 l pressure accumulator (BSP ½" IG connection). The system also offers a hydraulic connection with 20/30 L/min at 140 bar (incl. flat face couplings) for external applications. Installation is included in the price, the vehicle must be delivered to and collected from KW Hydraulik. Compressed air hose, welding cable set and remote control are not included in the scope of delivery. Further solutions for vehicles with power take-off (PTO) can be found here: Installation solutions. Manufacturer: FEP. HYDRO COMBY SW-F300 - PTO-GEAR is a power unit for installation in service and workshop vehicles.It can be installed in vehicles with rear-wheel drive and an existing PTO power take-off* on the transmission.The engine of your van serves as the drive for the generator, compressor and hydraulic pump.Equipment:230 Volt / 5 kVA / 16 A / CEE socket blue or SCHUKO400 Volt / 10 kVA / 16 A / CEE socket red300 ampere electrode welding unit with connection for cable remote controlConnection for welding cable plug SK 35/50 mandrel Ø13mm(Welding cable set and cable remote control not included in scope of delivery)Compressed air compressor, 1000 l/min. at 12 bar, connection BSP 1/2" IGHydraulic connection for external applications, 20/30 L/min. at 140 bar, FLATFACE couplingsScope of delivery:Hydraulic pump with adapter for PTO connectionPower generator unit with integrated welding unit with connection for cable remote control.Welding cable set and cable remote control not included in scope of deliveryCompressed air compressor with 25 litre accumulator,connectionBSP 1/2" internal threadSupplied without compressed air hose and accessoriesHydraulic tank, oil cooling, filterControl unit with vehicle-specific cables and adaptersPrice includes installation (hoses, etc.)The vehicle must be delivered to and collected from us for installation in your vehicle. These transfer costs are not included.* The power take-off must be prepared for the connection of a hydraulic pump; multi-tooth shaft.
Price on request
Discount %
PTO - belt-driven hydraulic pump for FIAT DUCATO 2.2
KAEW-FI262-SINGLE
The belt-driven hydraulic pump for the FIAT DUCATO 2.2 is perfect for vehicles built from 2021 onwards with a 2184 cm³ / 4-cylinder engine, air conditioning and front-wheel drive (FWD). Even without factory preparation, the system can be easily retrofitted using the complete installation kit with installation material. A magnetic clutch with 108 Nm at 12 volts (6PK belt) is used to ensure reliable power transmission. Depending on the application, hydraulic pumps from 4.5 to 28.2 cm³/revolution are available. When ordering, please specify the required flow rate and note the power limit of the magnetic coupling. The system is from KW Hydraulik and is ideal for mobile applications in the vehicle and municipal sector. Complete installation kit with installation material. FIAT DUCATO 2.2 from year of construction 2021Engine: 2184 cc / 4 cylinderswith air conditioningFront-wheel drive (FWD)No preparation available on the engineMagnetic clutch 108 Nm / 12 Volt (belt 6PK)Available hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!See also KAEW-FI262-TWIN with tandem pump and two oil circuits!
Selling price: €1,476.00 Regular price: €1,640.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for FIAT DUCATO 3.0
KAEW-FI258-SINGLE
The belt-driven hydraulic pump for the FIAT DUCATO 3.0 MULTIJET, CITROEN JUMPER 3.0 HDI and PEUGEOT BOXER 3.0 HDI is the ideal solution for vehicles built from 2006 onwards with a 2998 cm³ / 4-cylinder engine (F1C), air conditioning and front-wheel drive (FWD). Even without factory preparation, the system can be installed quickly and safely thanks to the complete installation kit with installation material. A magnetic clutch with 108 Nm at 12 volts (6PK belt) is used to ensure reliable power transmission. Hydraulic pumps with volumes from 4.5 to 28.2 cm³/revolution are available. When ordering, please specify the required flow rate and take into account the power limit of the magnetic coupling. The system comes from the experienced manufacturer KW Hydraulik and is optimally designed for mobile use in construction and municipal vehicles. Complete installation kit with installation material. FIAT DUCATO 3.0 MULTIJET / CITROEN JUMPER 3.0 HDI / PEUGEOT BOXER 3.0 HDIfrom model year 2006Engine: 2998 cc / 4 cylinders (F1C)with air conditioningFront-wheel drive (FWD)No preparation available on the engineMagnetic clutch 108 Nm / 12 Volt (belt 6PK)Available hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!See also KAEW-FI258-TWIN with tandem pump and two oil circuits!
Selling price: €1,548.00 Regular price: €1,720.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for FORD CUSTOM
KAEW-FO237-SINGLE
The belt-driven hydraulic pump for the FORD TRANSIT CUSTOM offers a sophisticated solution for vehicles from model year 2019 with a 2000 cm³ YNR6 engine, air conditioning and front-wheel drive (FWD). Even if there is no factory preparation on the engine, the system can be easily retrofitted as a complete installation kit including installation material. The built-in magnetic clutch (108 Nm, 12 volts) with 6PK belt drive ensures reliable power transmission. Hydraulic pumps from 4.5 to 28.2 cm³/revolution are available - please specify the required flow rate when ordering. The load limit of the magnetic coupling should always be observed. The system is from KW Hydraulik and is suitable for a wide range of mobile hydraulic applications in the municipal, construction or vehicle technology sectors. Complete installation kit with installation material. FORD TRANSIT CUSTOM from model year 2019Engine: 2000 cc / 4 cylinders (YNR6)with air conditioningFront-wheel drive (FWD)No preparation available on the engineMagnetic clutch 108 Nm / 12 Volt (belt 6PK)Available hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!See also KAEW-FO232-TWIN with tandem pump and two oil circuits!
Selling price: €1,197.00 Regular price: €1,330.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for FORD CUSTOM HYBRID
KAEW-FO242-SINGLE
The belt-driven hydraulic pump for the FORD TRANSIT CUSTOM HYBRID is the ideal retrofit solution for vehicles built from 2021 onwards with a 2000 cm³ YNR6 engine (hybrid), air conditioning and front-wheel drive (FWD). Even without factory preparation, the complete installation kit with installation material can be easily integrated. Thanks to the compact magnetic clutch with 108 Nm (12 volt, 6PK belt), the system can be used in a variety of ways. Depending on requirements, hydraulic pumps with delivery volumes between 4.5 and 28.2 cm³/revolution are available - please specify the required delivery volume when ordering. Please note the power limit of the magnetic coupling. The system is developed by KW Hydraulik and is ideal for mobile hydraulic applications in the municipal or vehicle sector. Complete installation kit with installation material. FORD TRANSIT CUSTOM HYBRIDfrom year of construction 2021Engine: 2000 cc / 4 cylinders (YNR6) / HYBRIDwith air conditioningFront-wheel drive (FWD)No preparation available on the engineMagnetic clutch 108 Nm / 12 Volt (belt 6PK)Available hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!See also KAEW-FO242-TWIN with tandem pump and two oil circuits!
Selling price: €1,449.00 Regular price: €1,610.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for IVECO DAILY 2.3 HPT
KAEW-IV340-SINGLE
The belt-driven hydraulic pump for the IVECO DAILY 2.3 HPT is a specially developed installation kit including installation material that enables simple retrofitting without factory engine preparation. Suitable for models built from 2022 onwards with a 2286 cm³ F1A engine, rear-wheel drive (RWD) and air conditioning, this system offers a robust and efficient solution for hydraulic applications in the commercial vehicle sector. The integrated magnetic clutch (140 Nm / 12 V) transmits the power to the hydraulic unit via an 8PK belt. There is a choice of hydraulic pumps from 4.5 to 28.2 cm³/rev, which can be individually combined. When ordering, please specify the desired flow rate and note the load limit of the magnetic coupling. Developed by KW Hydraulik, this system stands for reliable performance and high compatibility with current IVECO series. Complete installation kit with installation material. IVECO DAILY from model year 2022Engine: 2286 cc / 4 cylinders (F1A)with air conditioningRear-wheel drive (RWD)No preparation available on the engineMagnetic clutch 140 Nm / 12 Volt (belt 8PK)Available hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!See also KAEW-IV340-TWIN with tandem pump and two oil circuits!
Selling price: €1,845.00 Regular price: €2,050.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for IVECO DAILY 3.0 HPT
KAEW-IV344-SINGLE
The belt-driven hydraulic pump for the IVECO DAILY 3.0 HPT is a complete retrofit system including installation material that is ideal for vehicles built from 2022 onwards with a 2286 cm³ F1A engine, air conditioning and rear-wheel drive (RWD). This system can also be easily installed on models without factory preparation. The built-in magnetic clutch with 140 Nm at 12 volts reliably transmits the power to the hydraulic pump via an 8PK belt. For maximum flexibility, hydraulic pumps from 4.5 to 28.2 cm³/rev can be combined. The required flow rate must be specified when ordering. Important: Please note the power limit of the magnetic coupling. The system is made by KW Hydraulik and offers a durable solution for a wide range of applications in the field of mobile hydraulic systems. Complete installation kit with installation material. IVECO DAILY from model year 2022Engine: 2286 cc / 4 cylinders (F1A)with air conditioningRear-wheel drive (RWD)No preparation available on the engineMagnetic clutch 140 Nm / 12 Volt (belt 8PK)Available hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!See also KAEW-IV340-TWIN with tandem pump and two oil circuits!
Selling price: €2,223.00 Regular price: €2,470.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for MERCEDES SPRINTER FWD
KAEW-MB351-SINGLE
The belt-driven hydraulic pump for the MERCEDES SPRINTER FWD is ideal for retrofitting a hydraulic system to vehicles without factory-fitted engine preparation. The ready-to-install complete set from KW Hydraulik includes all installation materials and a powerful magnetic coupling with 140 Nm at 12 volts for the belt drive (8PK). The system is compatible with MERCEDES SPRINTER models from model year 2022 with 1950 cc OM654 engine, 4 cylinders, air conditioning and front-wheel drive (FWD). There are numerous hydraulic pump variants to choose from - from 4.5 to 28.2 cm³/rev, depending on the desired delivery rate. This must be specified when ordering. The pump can be used flexibly, for example for tippers, cable winches or loading cranes. Please note the power limit of the magnetic coupling when dimensioning.Complete installation kit with installation material. MERCEDES SPRINTER from model year 2022Engine: 1950 cc / 4 cylinders (OM654)with air conditioningFront-wheel drive (FWD)No preparation available on the engineMagnetic clutch 140 Nm / 12 Volt (belt 8PK)Available hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!See also KAEW-MB351-TWIN with tandem pump and two oil circuits!
Selling price: €1,719.00 Regular price: €1,910.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for MERCEDES SPRINTER RWD
KAEW-MB344-SINGLE
The belt-driven hydraulic pump for the MERCEDES SPRINTER RWD is the optimum solution for retrofitting hydraulic systems to vehicles without engine preparation. The complete installation kit from KW Hydraulik contains all the necessary components including a magnetic clutch with 140 Nm (12 volt) for the belt drive (8PK). Developed for the MERCEDES SPRINTER from model year 2021 with 1950 cc OM654 engine and rear-wheel drive (RWD), the system is suitable for both vehicles with and without air conditioning. The selection of hydraulic pumps ranges from 4.5 to 28.2 cm³/rev, so that a customised configuration is possible. The desired flow rate should be specified when ordering. Please note the power limit of the magnetic coupling to ensure optimum function.Complete installation kit with installation material. MERCEDES SPRINTER from year of construction 2021Engine: 1950 cc / 4 cylinders (OM654)With and without air conditioningRear-wheel drive (RWD)No preparation available on the engineMagnetic clutch 140 Nm / 12 Volt (belt 8PK)Available hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!See also KAEW-MB344-TWIN with tandem pump and two oil circuits!
Selling price: €1,764.00 Regular price: €1,960.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for Renault Master 2.3, FWD, with air conditioning, 140 Mn
KAEW-RE326-SINGLE
PTO - belt-driven hydraulic pump for Renault Master 2.3, FWD, with air conditioning, 140 Nm With the PTO installation kit from KW Hydraulik, you get a complete solution for retrofitting your Renault Master (from model year 2010) with a powerful hydraulic system. The unit includes all installation material and is specially designed for models with front-wheel drive (FWD) and air conditioning, where there is no preparation on the engine. The system is driven by a robust magnetic clutch with 140 Nm, 12 volt and 8PK belt profile. Depending on your requirements, you can choose from a wide range of hydraulic pumps: 4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 or 28.2 cc. Please be sure to specify the desired flow rate when ordering. Be sure to take into account the capacity of the magnetic coupling to ensure trouble-free operation. Ideally suited for the installation of hydraulic applications in the field of hydraulics for commercial vehicles and vans up to 7.5 tonnes. Complete installation kit with installation material. RENAUL MASTERfrom model year 2010Engine: ccm / 4 cylinderswith air conditioningFront-wheel drive (FWD)No preparation available on the engineMagnetic clutch 140 Nm / 12 Volt (belt 8PK)Available hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!
Selling price: €1,647.00 Regular price: €1,830.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for VW CRAFTER FWD & 4x4 - 108 Nm clutch
KAEW-VW217-SINGLE
Installation kit for belt-driven hydraulic pump - VW CRAFTER / MAN TGE (model year 2017-2022, front-wheel drive, FWD) This complete set for retrofitting a belt-driven hydraulic pump is specially designed for the VW CRAFTER and MAN TGE with front-wheel drive (FWD) - suitable for models from model year 2017 to 2022 with 2.0-litre 4-cylinder engine and air conditioning. The set can be easily installed even without factory preparation. The centrepiece of the system is a magnetic clutch with 108 Nm (12 V). The scope of delivery includes all mounting parts for the belt drive, installation accessories and a hydraulic pump of your choice. The flow rate is freely selectable - please specify the required size when ordering. Available pump sizes: 4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Complete installation kit with installation material:VW CRAFTER / MAN TGEfrom year of construction 2017-2022Engine: 1968 ccm / 4 cylinderswith air conditioningFront-wheel drive (FWD)No preparation available on the engineMagnetic clutch 108 Nm / 12 VoltAvailable hydraulic pumps:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccmPlease specify the required front quantity when ordering.See also KAEW-VW217-TWIN with tandem pump and two oil circuits!
Selling price: €1,431.00 Regular price: €1,590.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for VW CRAFTER FWD & 4x4 - 140 Nm clutch
KAEW-VW323-SINGLE
PTO - belt-driven hydraulic pump for VW CRAFTER FWD & 4x4 with 140 Nm clutch This installation kit from KW Hydraulik enables the professional drive of a hydraulic pump via the belt drive on the VW CRAFTER or MAN TGE - for models with front-wheel drive (FWD) or all-wheel drive (4x4) from model year 2018. The vehicles have a 2.0-litre 4-cylinder engine with air conditioning - factory preparation on the engine is not required. The set includes a powerful magnetic clutch with 140 Nm (12 V) as well as all necessary installation parts, belt pulleys and installation components. The hydraulic pump can be selected individually - please specify the required delivery rate when ordering. Available pump sizes: 4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Complete installation kit with installation material.VW CRAFTER / MAN TGEfrom year of construction 2018-Engine: 1968 ccm / 4 cylinderswith air conditioningFront-wheel drive (FWD)No preparation available on the engineMagnetic clutch 140 Nm / 12 voltAvailable hydraulic pumps:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccmPlease specify the required front quantity when ordering.See also KAEW-VW324-TWIN with tandem pump and two oil circuits!
Selling price: €1,602.00 Regular price: €1,780.00 (10% saved)
Discount %
PTO - belt-driven hydraulic pump for VW CRAFTER RWD
KAEW-VW219N-SINGLE
PTO - belt-driven hydraulic pump for VW CRAFTER RWD with 108 Nm clutch This complete installation kit from KW Hydraulik enables the retrofitting of a powerful belt-driven hydraulic pump on vehicles without factory preparation. It is specially designed for the VW CRAFTER / MAN TGE with rear-wheel drive (RWD) from model year 2017-2022. It is driven via a magnetic coupling with 108 Nm (12 V). The compact solution is ideal for a wide range of applications - from municipal use to special vehicles. Included in the set: Ready-to-install system with bracket, mounting material and magnetic coupling 108 Nm Important: The choice of pump must be matched to the power limit of the magnetic coupling. For higher requirements, a system with a reinforced coupling or tandem pump is recommended. Complete installation kit with installation material: VW CRAFTER / MAN TGEfrom year of construction 2017-2022Engine: 1968 cc / 4 cylinderswith air conditioningRear-wheel drive (RWD)No preparation available on the engineMagnetic clutch 108 Nm / 12 VoltAvailable hydraulic pumps that can be combined:4.5 / 6.4 / 7.0 / 8.3 / 9.6 / 11.5 / 14.1 / 16.0 / 17.9 / 21.1 / 23.7 / 25.5 / 28.2 ccm Please specify the required flow rate when ordering. Please note the performance of the magnetic coupling!See also KAEW-VW219-TWIN with tandem pump and two oil circuits!
Selling price: €1,431.00 Regular price: €1,590.00 (10% saved)
PTO-UG20kVA - Underfloor generator for vehicles with power take-off (PTO)
KWF-PTO-UG-20kVA-SET-IV
(5) Vehicle: Iveco Daily RWD + PTO
Complete installation of an underfloor generator set consisting of:Underfloor generatorCardan shaft for auxiliary driveCooling system complete with tankStandard power distributor (stainless steel on request)Standard mounting bracketThe vehicle must be delivered to and collected from us for installation in your vehicle. These transfer costs are not included.* The power take-off must be prepared for the connection of a shaft (SAE 87-4-8).Power: 20 kVAVoltage: 400/230 Volt +/-10%Frequency: 50 HzOutput speed of the power take-off: 1500 rpmCooling system: Water with antifreezeDrive shaft: SAE 87-4-8Connection for hydraulic pump: B5 / 112Torque at the shaft: 130 NmProtection class generator: IP65Protection class switch cabinet: IP23Weight: 65 kgSuitable for the following vehicles with power take-off:MERCEDES BENZ SPRINTERIVECO DAILY
Price on request
Discount %
ROAD CLEANER RC-H - Oil spill removal - High pressure cleaner and vacuum cleaner
KWF-ROAD CLEANER RC-H
The ROAD CLEANER RC-H is the compact solution for oil spill removal in vans such as the VW T6.1, VW Crafter FWD or FIAT Ducato, which do not have a power take-off (PTO). The drive via the vehicle engine produces no harmful exhaust fumes, which enables safe operation in the cargo area. The system combines a high-pressure cleaner and a vacuum cleaner, with the extracted liquid being collected in a stainless steel container. The hydraulic system requires 15 litres at 180 bar and is protected by a high-performance cooling system. Other safety features include a thermal circuit breaker, oil level monitor, pressure relief valve and emergency stop switch. The unit is operated via the 12-volt on-board power supply. A 300-litre stainless steel water tank, a 5-litre detergent tank, a washing lance, a hydraulic vacuum cleaner with a suction height of 3 metres and a hose reel with 10 metres of suction hose are already integrated. The system is approved for ATEX-1 and ATEX-21 zones and is ideal for use in potentially explosive atmospheres. You can find more information about the manufacturer here: FEP at KW Hydraulik. Application example: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. This model can be installed in vans that do not have a transmission with power take-off (PTO).VW-T6.1, VW Crafter FWD, FIAT Ducato, ....Driven by the vehicle engine, no harmful exhaust fumes are produced at the unit, which enables safe operation in the cargo area.The hydraulics drive either the high-pressure cleaner or the vacuum cleaner.The extracted liquid is collected in a stainless steel container.The unit can be used in ATEX-1 and ATEX-21 hazardous areas.FeaturesHydraulics: 15 litres at 180 barHydraulic system with high-performance cooling.Thermal protection switch, oil level monitoringPressure gauge and pressure relief valveControl unit with operating hours counterEmergency stop switch (disconnects the system from the drive)12 volt on-board voltage for system control300 litre stainless steel water tank with water separatorTank for cleaning additive 5 litres with proportion regulatorBrush for vacuum cleanerWash lance with high and low pressure nozzleHydraulic vacuum cleanerSuction height 3 metresHose reel with spring return for suction hose, 10 metres, hose diameter 38 mm40 litre tank for holding the oil-water mixture, switch-off when tank is fullApproval for ATEX-1 and ATEX-21 areasDimensions: 1400x1100xH1250mm Model ROAD CLEANER RC-HC with additional gas-powered water heater.
Selling price: €19,949.00 Regular price: €23,470.00 (15% saved)
ROAD CLEANER RC-H2 - Oil spill removal - High pressure cleaner and vacuum cleaner
KWF-ROAD CLEANER RC-H2
The ROAD CLEANER RC-H2 is the professional solution for oil spill removal in vehicles with a power take-off (PTO) such as the VW Crafter, MAN TGE, Mercedes Sprinter, IVECO Daily or Renault Master. It is driven by the vehicle engine - no harmful exhaust fumes are produced, which enables safe operation in the load compartment. Thanks to the simultaneous use of a high-pressure cleaner and vacuum cleaner, water consumption is reduced and cleaning is faster and more environmentally friendly. The extracted liquid is collected in a stainless steel tank. The system fulfils the requirements for ATEX-1 and ATEX-21 zones. Technical features: Hydraulic requirement 15 l/min at 180 bar, high-performance cooling, emergency stop switch, operating hours counter, 300-litre water tank, 10 m suction hose and 40-litre collection tank with automatic shut-off. You can find more information about the manufacturer here: FEP at KW Hydraulik. Area of application: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. This model is for installation in vehicles with transmission power take-off (PTO).VW CRAFTER / MAN TGEMERCEDES SPRINTERIVECO DAILYRENAULT MASTER / OPEL MOVANO / NISSAN NV400Driven by the vehicle engine, no harmful exhaust gases are produced at the unit, which enables safe operation in the load compartment.With this drive variant, the high-pressure cleaner can be operated simultaneously with the vacuum cleaner.This method requires less water, the work is faster and is more environmentally friendly.The extracted liquid is collected in a stainless steel container.The unit can be used in ATEX-1 and ATEX-21 hazardous areas.FeaturesHydraulics: 15 litres at 180 barHydraulic system with high-performance cooling.Thermal protection switch, oil level monitoringPressure gauge and pressure relief valveControl unit with operating hours counterEmergency stop switch (disconnects the system from the drive)12 volt on-board voltage for system control300 litre stainless steel water tank with water separatorTank for cleaning additive 5 litres with proportion regulatorBrush for vacuum cleanerWash lance with high and low pressure nozzleHydraulic vacuum cleanerSuction height 3 metresHose reel with spring return for suction hose, 10 metres, hose diameter 38 mm40 litre tank for holding the oil-water mixture, switch-off when tank is fullApproval for ATEX-1 and ATEX-21 areas Model ROAD CLEANER RC-H2C with additional gas-powered water heater.
Price on request
ROAD CLEANER RC-H2C - Oil spill removal - High-pressure cleaner with water heater and vacuum cleaner
KWF-ROAD CLEANER RC-H2C
The ROAD CLEANER RC-H2C combines a high-pressure cleaner, a hydraulic vacuum cleaner and an additional gas-powered water heater for efficient use in vehicles with a power take-off (PTO), such as the VW Crafter, MAN TGE, Mercedes Sprinter, IVECO Daily or Renault Master. It is operated via the vehicle engine so that no harmful exhaust fumes are emitted from the unit - ideal for safe use in the cargo area. Thanks to the option of operating cleaning and extraction at the same time, water consumption is minimised and working time is reduced. The extracted liquid is collected in a robust stainless steel tank. The ROAD CLEANER RC-H2C is also approved for use in potentially explosive atmospheres (ATEX-1 and ATEX-21). Technical highlights: Hydraulic requirement 15 l/min at 180 bar, high-performance cooling, operating hours counter, emergency stop switch, 300-litre water tank, suction hose with a length of 10 m and a 40-litre collection tank with fill level cut-off. You can find more information about the manufacturer here: FEP at KW Hydraulik. Area of application: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. This model is for installation in vehicles with transmission power take-off (PTO):VW CRAFTER / MAN TGEMERCEDES SPRINTERIVECO DAILYRENAULT MASTER / OPEL MOVANO / NISSAN NV400Driven by the vehicle engine, no harmful exhaust gases are produced at the unit, which enables safe operation in the load compartment.With this drive variant, the high-pressure cleaner can be operated simultaneously with the vacuum cleaner.This method requires less water, the work is faster and is more environmentally friendly.The extracted liquid is collected in a stainless steel container.The unit can be used in ATEX-1 and ATEX-21 hazardous areas.FeaturesHydraulics: 15 litres at 180 barHydraulic system with high-performance cooling.Thermal protection switch, oil level monitoringPressure gauge and pressure relief valveControl unit with operating hours counterEmergency stop switch (disconnects the system from the drive)12 volt on-board voltage for system control300 litre stainless steel water tank with water separatorTank for cleaning additive 5 litres with proportion regulatorBrush for vacuum cleanerWash lance with high and low pressure nozzleHydraulic vacuum cleanerSuction height 3 metresHose reel with spring return for suction hose, 10 metres, hose diameter 38 mm40 litre tank for holding the oil-water mixture, switch-off when tank is fullApproval for ATEX-1 and ATEX-21 areas Model ROAD CLEANER RC-H2C with additional gas-powered water heater.
Price on request
ROAD CLEANER RC-HC - Oil spill removal - High-pressure cleaner with water heater and vacuum cleaner
KWF-ROAD CLEANER RC-HC
The ROAD CLEANER RC-HC is a versatile high-pressure cleaner with vacuum cleaner and gas-powered water heater for installation in vans without a power take-off (PTO) such as the VW T6.1, VW Crafter FWD or FIAT Ducato. It is driven by the vehicle engine - this means that no harmful exhaust fumes are produced, which enables safe operation in the load compartment. The hydraulics drive either the high-pressure cleaner or the vacuum cleaner. The integrated hot water flow heater makes cleaning faster and more efficient, even in cold temperatures. Liquids are reliably collected in a stainless steel tank. The system is also approved for use in ATEX-1 and ATEX-21 areas. Technical details: Hydraulic requirement 15 l/min at 180 bar, high-performance cooling, 300-litre water tank, 10 m suction hose and 40-litre collection tank with automatic shut-off. Find out more about the manufacturer here: FEP at KW Hydraulik. You can find suitable applications here: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. This model can be installed in vans that do not have a transmission with power take-off (PTO).VW-T6.1, VW Crafter FWD, FIAT Ducato, ....Driven by the vehicle engine, no harmful exhaust fumes are produced at the unit, which enables safe operation in the cargo area.The hydraulics drive either the high-pressure cleaner or the vacuum cleaner.This version has an additional gas-fuelled instantaneous water heater. Hot water enables use in cold outside temperatures and removes dirt better.The extracted liquid is collected in a stainless steel container.The unit can be used in ATEX-1 and ATEX-21 hazardous areas.FeaturesHydraulics: 15 litres at 180 barHydraulic system with high-performance cooling.Thermal protection switch, oil level monitoringPressure gauge and pressure relief valveControl unit with operating hours counterEmergency stop switch (disconnects the system from the drive)12 volt on-board voltage for system control300 litre stainless steel water tank with water separatorTank for cleaning additive 5 litres with proportion regulatorBrush for vacuum cleanerWash lance with high and low pressure nozzleHydraulic vacuum cleanerSuction height 3 metresHose reel with spring return for suction hose, 10 metres, hose diameter 38 mm40 litre tank for holding the oil-water mixture, switch-off when tank is fullApproval for ATEX-1 and ATEX-21 areasDimensions: 1400x1100xH1250mm Model ROAD CLEANER RC-HC with additional gas-powered water heater.
Price on request
Discount %
ROAD CLEANER RC-M - Oil spill removal - High pressure cleaner and vacuum cleaner
KWF-ROAD CLEANER RC-M
The ROAD CLEANER RC-M module is the flexible solution for oil spill removal on vehicles with a loading area or trailer. It is simply attached and is immediately ready for use - also ideal for small vans or trailers. The integrated petrol engine with electric starter drives a hydraulic pump that supplies either the high-pressure cleaner or the vacuum cleaner. The extracted liquid is safely collected in a stainless steel tank. The system is approved for use in potentially explosive atmospheres (ATEX-1 and ATEX-21) and has a 300 litre water tank, oil cooler, 18 metres of high-pressure hose and 10 metres of suction hose. You can find out more about the manufacturer here: FEP at KW Hydraulik. Applications for this module can be found here: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. This module can be used perfectly on vehicles with a loading area or on trailers.It is mounted on the cargo bed as required and can be used immediately.Even the smallest vehicles and even trailers can be used for transport.The integrated motor is started with an electric starter . This drives a hydraulic pump, which in turn alternately drivesa high-pressure cleaner and a vacuum cleaner.The extracted liquid is collected in a stainless steel container.The unit can be used in ATEX-1 and ATEX-21 hazardous areas.FeaturesPetrol engine with electric starter (supplied without battery and prepared for connection to the vehicle electrical system)Hydraulics: 15 litres at 180 barHydraulic system with 10 litre hydraulic tank, oil cooler300 litre stainless steel water tank with water separatorTank for cleaning additive 5 litres with proportion regulatorHose reel with spring return for high-pressure hose, 18 metresWash lance with high and low pressure nozzleHydraulic vacuum cleanerSuction height 3 metresHose reel with spring return for suction hose, 10 metres, hose diameter 38 mmBrush for vacuum cleaner40 litre tank for holding the oil-water mixture, switch-off when tank is fullApproval for ATEX-1 and ATEX-21 areasDimensions: 1400x1100xH1250mmModel ROAD CLEANER RC-MC with additional gas-powered water heater.
Selling price: €19,414.00 Regular price: €22,840.00 (15% saved)
Products